Scalarworks SYNC/01 - Red Dot mounts for Shotguns - hero

Sync/01

Cutting Edge Red Dot mounts for Benelli shotguns.

Enhance the effectiveness of your shotgun with the speed and precision of a red dot sight, while maintaining its factory shooting ergonomics.

Perfect Placement

Puts your Red Dot in the ideal shooting position.

Scalarworks Sync/Benelli Trijicon RMR mount for Benelli Shotguns - co-witness

STRENGTH IN NUMBERS

The Sync's patented internal Key-Slot mounting system spreads side impacts across 4 anchor points.

7075-T6
7075-T6
Scalarworks Sync mount 7075-T6 vs 6061-T6

Every Sync is CNC milled from 7075-T6 billet, which has vastly superior mechanical properties to 6061-T6, and is used where ultimate strength and durability outweigh cost considerations.

Scalarworks SYNC/01 - Red Dot mount for Benelli Shotguns - lightweight

LIGHT MADE RIGHT

Meticulously machined to be the lightest optic mounting solution for Benelli Tactical shotguns, without compromising an ounce of strength.

Scalarworks® Sync SW1100 (0.64oz)
24%
Benelli® 70069 rail + Trijicon® RM33 Low Mount (2.71oz)
100%

All Trademarks are the property of their respective owners and used in accordance with FTC Comparative Advertising guidelines. All parts weighed under the same conditions including rail screws.

WATERTIGHT

Scalarworks SYNC/01 - red dot mount for Benelli Shotguns - watertight

The Sync features a watertight mounting platform that doesn't require a sealing plate.

CLEARANCE

Scalarworks SYNC/01 Benelli - Aimpoint Micro T-2 mount for Benelli Shotguns - deliberate

The Sync features a scallop to comfortably clear the factory flip-up caps.

BUNDLE UP

Worry-free, properly torqued and threadlocked, optic bundles.

Scalarworks SYNC Trijicon RMR Mount for Benelli m4 (Hero)

SYNC/01

(187 customer reviews)

$119.00 – $929.00

Clear
SKU: SW11XX
SPECS
Choose a Configuration Above.
COMPATIBILITY
Choose a Configuration Above.
INCLUDED
Choose a Configuration Above.

187 reviews for SYNC/01

Add a review

Your email address will not be published. Required fields are marked *

  1. Allan –

    Great product, only issue I have is with the red locktite….If you are planning on removing the mount from your gun, DO NOT keep the red locktite on the screws…they WILL NOT come back out, I stripped the included torx bit along with 6..yes 6 other bits and still couldn’t remove the screws, and they were only installed with light pressure, not even torqued!!…only way I could get them out was to literally take a grinding bit and grind a flat slit into the screw( and part of the mount) wide enough to get a thick flat head screw driver in and I was finally able to get enough force to loosen the screw. Red locktite is great if permanent, but the included screws should have blue locktite( removeable) not red

    (0) (2)

    • Scalarworks (store manager) –

      Sorry to hear that. This isn’t normal behavior and there is likely something else going on. The red compound on the supplied screws is not loctite threadlocker, but rather a nylon patch that provides the same amount of resistance going in as it doesn’t going out. Please contact our support team through our contact page and they will investigate further.

  2. Thomas –

    It was too low for me. I’d prefer 1/3 co-witness. Actually, perfection would be a very, very low RMR pic rail mount. Wish scalarworks would do that.

    (1) (4)

    • Scalarworks (store manager) –

      Hi, Thomas. We’re not sure we understand what you mean: The RMR sits only 2.65mm from the very top of the receiver, providing as deep of a co-witness as is physically possible without milling the top of the shotgun receiver. A lower-third co-witness would put the RMR in the way of the shotgun bolt carrier group.